• P1 Poort Slimme Meter USB to RJ12 Adapter cable
  • P1 Poort Slimme Meter USB to RJ12 Adapter cable
  • P1 Poort Slimme Meter USB to RJ12 Adapter cable

P1 Poort Slimme Meter USB to RJ12 Adapter cable

SKU
ACS.1137
Customer #
MOQ
10
Packaging
1pcs/lot
Unit Price
RFQ

Payment Accepted

Bulk Order

Unit Price

<20 RFQ
20+ RFQ
50+ RFQ
200+ RFQ

Buyer Protection

  • Full Refund if you don't receive your order
  • Full or Partial Refund, if the item is not as described

About FT232RL

The FT232R is the latest device to be added to FTDI’s range of USB UART interface Integrated Circuit Devices. The FT232R is a USB to serial UART interface with optional clock generator output, and the new FTDIChip-ID? security dongle feature. In addition, asynchronous and synchronous bit bang interface modes are available. USB to serial designs using the FT232R have been further simplified by fully integrating the external EEPROM, clock circuit and USB resistors onto the device.

The FT232R adds two new functions compared with its predecessors, effectively making it a "3-in-1" chip for some application areas. The internally generated clock (6MHz, 12MHz, 24MHz, and 48MHz) can be brought out of the device and used to drive a microcontroller or external logic. A unique number (the FTDIChip-ID) is burnt into the device during manufacture and is readable over USB, thus forming the basis of a security dongle which can be used to protect customer application software from being copied.

  • Single chip USB to asynchronous serial data transfer interface.

  • Entire USB protocol handled on the chip - No USB-specific firmware programming required.

  • UART interface support for 7 or 8 data bits, 1 or 2 stop bits and odd / even / mark / space / no parity.

  • Fully assisted hardware or X-On / X-Off software handshaking.

  • Data transfer rates from 300 baud to 3 Megabaud (RS422 / RS485 and at TTL levels) and 300 baud to 1 Megabaud (RS232).

  • In-built support for event characters and line break condition.

  • New USB FTDIChip-ID? feature.

  • New configurable CBUS I/O pins.

  • Auto transmit buffer control for RS485 applications.

  • Transmit and receive LED drive signals.

  • New 48MHz, 24MHz,12MHz, and 6MHz clock output signal Options for driving external MCU or FPGA.

  • FIFO receive and transmit buffers for high data throughput.

  • 256 Byte receive buffer and 128 Byte transmit buffer utilising buffer smoothing technology to allow for high data throughput.

  • Adjustable receive buffer timeout.

  • Synchronous and asynchronous bit bang mode interface options with RD# and WR# strobes.

  • New CBUS bit bang mode option.

  • Integrated 1024 bit internal EEPROM for I/O configuration and storing USB VID, PID, serial number and product description strings.

  • Device supplied preprogrammed with unique USB serial number.

  • Support for USB suspend / resume.

  • Support for bus powered, self powered, and high-power bus powered USB configurations.

  • Integrated 3.3V level converter for USB I/O .

  • Integrated level converter on UART and CBUS for interfacing to 5V - 1.8V Logic.

  • True 5V / 3.3V / 2.8V / 1.8V CMOS drive output and TTL input.

  • High I/O pin output drive option.

  • Integrated USB resistors.

  • Integrated power-on-reset circuit.

  • Fully integrated clock - no external crystal, oscillator, or resonator required.

  • Fully integrated AVCC supply filtering - No separate AVCC pin and no external R-C filter required.

  • UART signal inversion option.

  • USB bulk transfer mode.

  • 3.3V to 5.25V Single Supply Operation.

  • Low operating and USB suspend current.

  • Low USB bandwidth consumption.

  • UHCI / OHCI / EHCI host controller compatible.

  • USB 2.0 Full Speed compatible.

  • -40°C to 85°C extended operating temperature range.

Supported Operating System of USB to RJ11 6P4C RS232 Serial Cable
Drivers are available which allow USB FTDI devices to work with the following operating systems
1.   For Windows 8 x32
2.   For Windows 8 x64
3.   For Windows Server 2008 R2 x64
4.   For Windows 7 x32
5.   For Windows 7 x64
6.   For Windows Server 2008            
7.   For Windows Server 2008 x64            
8.   For Windows Vista x32           
9.   For Windows Vista x64
10. For Windows Server 2003 x32
11. For Windows Server 2003 x64
12. For Windows XP x32
13. For Windows XP x64
14. For Windows ME
15. For Windows 98
16. For Linux
17. For Mac OS X
18. For Mac OS 9
19. For Mac OS 8
20  For Windows CE.NET (Version 4.2 and greater)
21. For Android


Important notes:

In case of not responsible for the third party software.(please go to Meade official website. www.meade.com to download it)

It is RS232 Serial Signal Level Cable, please confirm your device is match with this pin Assignment .


The P1 port is working according DSMR-4.0.Interface

The data from the P1 port is serial data, and is connectable with a RJ12[6p6C] connector, and has the following signals:

https://sc02.alicdn.com/kf/HTB11i0gSFXXXXbKapXXq6xXFXXXK.jpg


Cable pin assignment type 1 (please specify when ordering)

https://ae01.alicdn.com/kf/HTB1BonyXIfrK1Rjy0Fmq6xhEXXa8.jpg


Cable pin assignment type 2 (please specify when ordering)


ME382 MT382 AMAZON RJ12 6P6C



FTDI Driver : https://www.ftdichip.com/Drivers/VCP.htm

Installation Guide:http://www.ftdichip.com/Support/Documents/InstallGuides.htm


Package includes:

1 X P1 Poort Slimme Meter USB to RJ12 Adapter cable


Note: all the descriptions and prices are subject to change without prior notice.

Free Shipping: No

Shipping Weight/Unit(g): 0.00

Std. Packing Qty. (pcs): 1

Report an Error (Win $10 Prize)